代码收藏家 RT-Thread STM32L475VET6实现USB鼠标模拟详解
文章目录
前言
本文采用开发板为STM32L475VET6(潘多拉开发板),使用RT_Thread Studio基于芯片开发模式，系统版本为4.0.3，完成模拟鼠标实验，实现鼠标功能，左键为KEY0，右键为KEY2
一、板载资源
icm20608传感器采用I2C协议，本文采用软件模拟I2C
查阅数据手册：开发板使用的是 PC0 模拟时钟线SCL、PC1 模拟数据线 SDA，
二、具体步骤
1.配置icm20608传感器
RT-Thread+STM32L475VET6——icm20608传感器
2.打开CubeMX进行USB配置
生成工程
3. 配置USB
按照官方步骤配置
3.1 打开USB驱动
3.2 声明USB
3.3 剪切stm32xxxx_hal_msp.c中的void HAL_PCD_MspInit(PCD_HandleTypeDef* hpcd)和void HAL_PCD_MspDeInit(PCD_HandleTypeDef* hpcd)函数至board.c
3.4 使能USB
一般默认开启
4. 编译，烧录
示例代码
#include <rtthread.h>
#include <rtdevice.h>
#include <board.h>
#include "icm20608.h"
#include <math.h>
#define DBG_SECTION_NAME "3D_mouse"
#define DBG_LEVEL DBG_LOG
#include <rtdbg.h>
#define PIN_KEY0 GET_PIN(D,10)
#define PIN_KEY2 GET_PIN(D,8)
static rt_sem_t mouse_sem = RT_NULL;
static struct rt_thread usb_thread;
ALIGN(RT_ALIGN_SIZE)
static char usb_thread_stack[0x1000];
static struct rt_thread icm_thread;
ALIGN(RT_ALIGN_SIZE)
static char icm_thread_stack[0x1000];
static struct rt_thread key_thread;
ALIGN(RT_ALIGN_SIZE)
static char key_thread_stack[0x1000];
/* 变动识别值 */
const static float mouse_rang_scope = 6.0f;
/* 读取角度有效角度 */
const static float mouse_angle_range = 80.0f;
/* 移动值的最大值 */
const static float mouse_move_range = 127.0f;
/* 角度移动比 */
#define mouse_ratio (mouse_move_range / mouse_angle_range)
/* 移动步长 */
const static rt_uint8_t mouse_pixel_len = 5;
/* 鼠标响应时间 */
const static rt_uint32_t mouse_sample_times = 0;
static float mouse_cmp_last_x, mouse_cmp_last_y;
#define Gyro_Gr 0.0010653f
#define pi 3.141593f
#define Kp 10.0f
#define Ki 0.008f
#define halfT 0.01f
static float q0 = 1, q1 = 0, q2 = 0, q3 = 0;
static float exInt = 0, eyInt = 0, ezInt = 0;
struct icm_position
{
icm20608_device_t icm20608_device;
rt_mutex_t lock;
float x; // 传感器 x 位置
float y; // 传感器 y 位置
float z; // 传感器 z 位置
rt_int8_t buff[4]; // 发送鼠标的值
};
typedef struct icm_position *icm_position_t;
icm_position_t icm_device = RT_NULL;
static void mouse_meas_check(float *temp)
{
if (*temp > mouse_angle_range)
{
*temp = mouse_angle_range;
}
else if (*temp < -mouse_angle_range)
{
*temp = -mouse_angle_range;
}
}
#ifdef __GNUC__
const float __atan2f_lut[4] = {
-0.0443265554792128, //p7
-0.3258083974640975, //p3
+0.1555786518463281, //p5
+0.9997878412794807 //p1
};
const float __atan2f_pi_2 = 1.5707963;
/* 求平方根 */
static float _sqrt(float x)
{
float xhalf = 0.5f * x;
int i = *(int *)&x;
i = 0x5f375a86 - (i >> 1);
x = *(float *)&i;
x = x * (1.5f - xhalf * x * x);
return 1.0 / x;
}
/* 求绝对值 */
static float _fabs(float x)
{
return (x >= 0 ? x : (-x));
}
/* 求x / y的反正切值 */
static float _atan2f(float y, float x)
{
float a, b, c, r, xx;
int m;
union {
float f;
int i;
} xinv;
xx = _fabs(x);
xinv.f = xx;
m = 0x3F800000 - (xinv.i & 0x7F800000);
xinv.i = xinv.i + m;
xinv.f = 1.41176471f - 0.47058824f * xinv.f;
xinv.i = xinv.i + m;
b = 2.0 - xinv.f * xx;
xinv.f = xinv.f * b;
b = 2.0 - xinv.f * xx;
xinv.f = xinv.f * b;
c = _fabs(y * xinv.f);
xinv.f = c;
m = 0x3F800000 - (xinv.i & 0x7F800000);
xinv.i = xinv.i + m;
xinv.f = 1.41176471f - 0.47058824f * xinv.f;
xinv.i = xinv.i + m;
b = 2.0 - xinv.f * c;
xinv.f = xinv.f * b;
b = 2.0 - xinv.f * c;
xinv.f = xinv.f * b;
xinv.f = xinv.f + c;
a = (c > 1.0f);
c = c - a * xinv.f;
r = a * __atan2f_pi_2;
xx = c * c;
a = (__atan2f_lut[0] * c) * xx + (__atan2f_lut[2] * c);
b = (__atan2f_lut[1] * c) * xx + (__atan2f_lut[3] * c);
xx = xx * xx;
r = r + a * xx;
r = r + b;
b = M_PI;
b = b - 2.0f * r;
r = r + (x < 0.0f) * b;
b = (_fabs(x) < 0.000001f);
c = !b;
r = c * r;
r = r + __atan2f_pi_2 * b;
b = r + r;
r = r - (y < 0.0f) * b;
return r;
}
static double _asin(double x)
{
return _atan2f(x, _sqrt(1.0 - x * x));
}
#endif /* __GNUC__ */
/* 获取俯仰角、偏航角、翻滚角 */
static void get_angle(icm_position_t dev, float ax, float ay, float az, float gx, float gy, float gz)
{
float pitch = 0, roll = 0, yaw = 0;
float norm;
float vx, vy, vz;
float ex, ey, ez;
float q0q0 = q0 * q0;
float q0q1 = q0 * q1;
float q0q2 = q0 * q2;
float q1q1 = q1 * q1;
float q1q3 = q1 * q3;
float q2q2 = q2 * q2;
float q2q3 = q2 * q3;
float q3q3 = q3 * q3;
gx *= Gyro_Gr;
gy *= Gyro_Gr;
gz *= Gyro_Gr;
if (az == 0)
return;
#ifdef __GNUC__
norm = _sqrt(ax * ax + ay * ay + az * az);
#else
norm = sqrt(ax * ax + ay * ay + az * az);
#endif /* __GNUC__ */
ax = ax / norm;
ay = ay / norm;
az = az / norm;
vx = 2 * (q1q3 - q0q2);
vy = 2 * (q0q1 + q2q3);
vz = q0q0 - q1q1 - q2q2 + q3q3;
ex = (ay * vz - az * vy);
ey = (az * vx - ax * vz);
ez = (ax * vy - ay * vx);
exInt = exInt + ex * Ki;
eyInt = eyInt + ey * Ki;
ezInt = ezInt + ez * Ki;
gx = gx + Kp * ex + exInt;
gy = gy + Kp * ey + eyInt;
gz = gz + Kp * ez + ezInt;
q0 = q0 + (-q1 * gx - q2 * gy - q3 * gz) * halfT;
q1 = q1 + (q0 * gx + q2 * gz - q3 * gy) * halfT;
q2 = q2 + (q0 * gy - q1 * gz + q3 * gx) * halfT;
q3 = q3 + (q0 * gz + q1 * gy - q2 * gx) * halfT;
#ifdef __GNUC__
norm = _sqrt(q0 * q0 + q1 * q1 + q2 * q2 + q3 * q3);
#else
norm = sqrt(q0 * q0 + q1 * q1 + q2 * q2 + q3 * q3);
#endif /* __GNUC__ */
q0 = q0 / norm;
q1 = q1 / norm;
q2 = q2 / norm;
q3 = q3 / norm;
#ifdef __GNUC__
pitch = -_asin(2 * (q0 * q2 - q1 * q3)) * 57.2957795f;
roll = _asin(2 * (q0 * q1 + q2 * q3)) * 57.2957795f;
yaw = -_atan2f(2 * (q1 * q2 + q0 * q3), (q0q0 + q1q1 - q2q2 - q3q3)) * 57.29578f;
#else
pitch = -asin(2 * (q0 * q2 - q1 * q3)) * 57.2957795f;
roll = asin(2 * (q0 * q1 + q2 * q3)) * 57.2957795f;
yaw = -atan2f(2 * (q1 * q2 + q0 * q3), (q0q0 + q1q1 - q2q2 - q3q3)) * 57.29578f;
#endif /* __GNUC__ */
mouse_meas_check(&pitch);
dev->x = pitch * mouse_ratio;
mouse_meas_check(&roll);
dev->y = roll * mouse_ratio;
mouse_meas_check(&yaw);
dev->z = yaw * mouse_ratio;
}
static void mouse_get_pos(icm_position_t dev)
{
rt_err_t result;
rt_int16_t accel_x, accel_y, accel_z;
rt_int16_t gyros_x, gyros_y, gyros_z;
RT_ASSERT(dev);
result = rt_mutex_take(dev->lock, RT_WAITING_FOREVER);
if (result != RT_EOK)
{
goto __exit;
}
result = icm20608_get_accel(dev->icm20608_device, &accel_x, &accel_y, &accel_z);
if (result != RT_EOK)
{
rt_mutex_release(dev->lock);
goto __exit;
}
result = icm20608_get_gyro(dev->icm20608_device, &gyros_x, &gyros_y, &gyros_z);
if (result != RT_EOK)
{
rt_mutex_release(dev->lock);
goto __exit;
}
get_angle(dev, (float)accel_x, (float)accel_y, (float)accel_z, (float)gyros_x, (float)gyros_y, (float)gyros_z);
rt_mutex_release(dev->lock);
__exit:
if (result != RT_EOK)
{
LOG_E("The sensor does not work");
return;
}
}
static icm_position_t mouse_init_icm(void)
{
rt_err_t result;
rt_thread_mdelay(1000);
icm_device = rt_calloc(1, sizeof(struct icm_position));
if (icm_device == RT_NULL)
{
LOG_E("Can't allocate memory for three-dimensional mouse ");
return RT_NULL;
}
/* 初始化传感器 icm20608 */
icm_device->icm20608_device = icm20608_init("i2c3");
if (icm_device->icm20608_device == RT_NULL)
{
LOG_E("The sensor initializes failure");
rt_free(icm_device);
return RT_NULL;
}
else
{
LOG_D("The 3D mouse initializes success");
}
icm_device->lock = rt_mutex_create("mutex_mouse", RT_IPC_FLAG_FIFO);
if (icm_device->lock == RT_NULL)
{
LOG_E("Can't create mutex for three-dimensional mouse");
rt_free(icm_device);
return RT_NULL;
}
mouse_sem = rt_sem_create("mouse_sem", 0, RT_IPC_FLAG_FIFO);
if (mouse_sem == RT_NULL)
{
LOG_E("Can't create sem for mouse device");
rt_mutex_delete(icm_device->lock);
rt_free(icm_device);
return 0;
}
/* 传感器零值校准 */
result = icm20608_calib_level(icm_device->icm20608_device, 10);
if (result != RT_EOK)
{
LOG_E("The sensor calibrates failure");
rt_mutex_delete(icm_device->lock);
rt_sem_delete(mouse_sem);
rt_free(icm_device);
return RT_NULL;
}
return icm_device;
}
static void mouse_go_release_status(void)
{
/* 初始状态值 */
rt_int8_t buff[4] = {0x08, 0, 0, 0};
icm_device->buff[0] = buff[0];
icm_device->buff[1] = buff[1];
icm_device->buff[2] = buff[2];
icm_device->buff[3] = buff[3];
}
static void mouse_send_data(rt_device_t device)
{
RT_ASSERT(device != RT_NULL);
rt_device_write(device, HID_REPORT_ID_MOUSE, icm_device->buff, 4);
mouse_go_release_status();
}
/* 负值表示向左移动，正值表示向右移动 */
static void mouse_move_x(rt_device_t device, float ratio_x)
{
RT_ASSERT(device != RT_NULL);
if (icm_device->x < 0)
{
icm_device->buff[1] = (rt_int8_t)(-mouse_pixel_len * ratio_x);
}
else
{
icm_device->buff[1] = (rt_int8_t)(mouse_pixel_len * ratio_x);
}
mouse_send_data(device);
}
/* 正值表示向下移动，负值表示向上移动 */
static void mouse_move_y(rt_device_t device, float ratio_y)
{
RT_ASSERT(device != RT_NULL);
if (icm_device->y < 0)
{
icm_device->buff[2] = (rt_int8_t)(-mouse_pixel_len * ratio_y);
}
else
{
icm_device->buff[2] = (rt_int8_t)(mouse_pixel_len * ratio_y);
}
mouse_send_data(device);
}
static void mouse_move_xy(rt_device_t device, float ratio_x, float ratio_y)
{
RT_ASSERT(device != RT_NULL);
if (icm_device->x < 0)
{
icm_device->buff[1] = (rt_int8_t)(-mouse_pixel_len * ratio_x);
}
else
{
icm_device->buff[1] = (rt_int8_t)(mouse_pixel_len * ratio_x);
}
if (icm_device->y < 0)
{
icm_device->buff[2] = (rt_int8_t)(-mouse_pixel_len * ratio_y);
}
else
{
icm_device->buff[2] = (rt_int8_t)(mouse_pixel_len * ratio_y);
}
mouse_send_data(device);
}
static void usb_thread_entry(void *parameter)
{
rt_device_t device = (rt_device_t)parameter;
rt_uint8_t i = 0;
while (1)
{
if (rt_sem_take(mouse_sem, RT_WAITING_FOREVER) == RT_EOK)
{
rt_uint8_t temp_x = 0, temp_y = 0, move_max = 0;
float move_distance = 0.0f;
rt_mutex_take(icm_device->lock, RT_WAITING_FOREVER);
#ifdef __GNUC__
temp_x = (rt_uint8_t)_fabs(icm_device->x);
temp_y = (rt_uint8_t)_fabs(icm_device->y);
move_distance = _sqrt(temp_x * temp_x + temp_y * temp_y);
#else
temp_x = (rt_uint8_t)fabs(icm_device->x);
temp_y = (rt_uint8_t)fabs(icm_device->y);
move_distance = sqrt(temp_x * temp_x + temp_y * temp_y);
#endif
move_max = temp_x > temp_y ? temp_x : temp_y;
/* 根据倾斜程度获取移动值 */
for (i = 0; i < move_max / mouse_pixel_len; i++)
{
LOG_D("move_max :%4d, x: %4d, y :%4d ", move_max, temp_x, temp_y);
if (i < temp_x && i < temp_y)
{
mouse_move_xy(device, temp_x / move_distance, temp_y / move_distance);
}
else if (i < temp_x && i >= temp_y)
{
mouse_move_x(device, temp_x / move_distance);
}
else if (i >= temp_x && i < temp_y)
{
mouse_move_y(device, temp_y / move_distance);
}
else
{
break;
}
}
rt_mutex_release(icm_device->lock);
}
rt_thread_mdelay(mouse_sample_times);
}
}
static void icm_thread_entry(void *parameter)
{
while (1)
{
float temp_x = 0.0, temp_y = 0.0;
rt_mutex_take(icm_device->lock, RT_WAITING_FOREVER);
/* 获取鼠标移动范围 */
mouse_get_pos(icm_device);
/* 获取差值 */
temp_x = icm_device->x - mouse_cmp_last_x;
temp_y = icm_device->y - mouse_cmp_last_y;
/* 避免抖动 */
if (temp_x > mouse_rang_scope || temp_x < -mouse_rang_scope || temp_y > mouse_rang_scope || temp_y < -mouse_rang_scope)
{
/* 存储这次鼠标位移值 */
mouse_cmp_last_x = icm_device->x;
mouse_cmp_last_y = icm_device->y;
rt_sem_release(mouse_sem);
}
rt_mutex_release(icm_device->lock);
rt_thread_mdelay(mouse_sample_times);
}
}
static void key_thread_entry(void *parameter)
{
int mouse_key_2, mouse_key_0;
rt_device_t device = (rt_device_t)parameter;
rt_err_t result = -RT_ERROR;
while (1)
{
if (rt_pin_read(PIN_KEY0) == PIN_LOW)
{
mouse_key_0 = 1;
}
else if (rt_pin_read(PIN_KEY2) == PIN_LOW)
{
mouse_key_2 = 1;
}
else
{
mouse_key_2 = 0;
mouse_key_0 = 0;
}
if (mouse_key_2 | mouse_key_0)
{
result = rt_mutex_take(icm_device->lock, RT_WAITING_FOREVER);
if (result == RT_EOK)
{
/* 获取鼠标键值，默认为 0 */
icm_device->buff[0] = 0x08 | mouse_key_2 | mouse_key_0 << 1;
if (mouse_key_2 & mouse_key_0)
{
LOG_D("left & right down");
}
else if (mouse_key_2)
{
LOG_D("left down");
}
else if (mouse_key_0)
{
LOG_D("right down");
}
mouse_send_data(device);
rt_mutex_release(icm_device->lock);
rt_thread_mdelay(50);
}
}
rt_thread_mdelay(mouse_sample_times / 5);
}
}
static void mouse_init_key(void)
{
/* 鼠标左键 */
rt_pin_mode(PIN_KEY0, PIN_MODE_INPUT);
/* 鼠标右键 */
rt_pin_mode(PIN_KEY2, PIN_MODE_INPUT);
}
int main(void)
{
return 0;
}
static int application_usb_init(void)
{
/* 查找名称为 hidd 的设备 */
rt_device_t device = rt_device_find("hidd");
/* 初始化六轴传感器设备 */
icm_device = mouse_init_icm();
/* 初始化按键 */
mouse_init_key();
RT_ASSERT(device != RT_NULL);
RT_ASSERT(icm_device != RT_NULL);
/*打开查找到的 hid 设备 */
rt_device_open(device, RT_DEVICE_FLAG_WRONLY);
/* 初始化 USB 线程*/
rt_thread_init(&usb_thread,
"hidd",
usb_thread_entry, device,
usb_thread_stack, sizeof(usb_thread_stack),
10, 20);
rt_thread_startup(&usb_thread);
/* 初始化六轴传感器线程 */
rt_thread_init(&icm_thread,
"icm20608",
icm_thread_entry, RT_NULL,
icm_thread_stack, sizeof(icm_thread_stack),
10, 20);
rt_thread_startup(&icm_thread);
/* 初始化按键线程 */
rt_thread_init(&key_thread,
"key",
key_thread_entry, device,
key_thread_stack, sizeof(key_thread_stack),
10, 20);
rt_thread_startup(&key_thread);
return 0;
}
INIT_APP_EXPORT(application_usb_init);
烧录完成后，将开发板上的USB OTG 连接PC端的USB接口，即可实现鼠标功能。
作者：苏慕TRYACE
